Best Of
Solar panel specs on 2021 Tab 400
What is the wattage on the 2021 Tab 400 roof Solar Panel? I have seen everywhere from 105 to 190 watts. Does anyone know for sure?
Re: Large Rigid Solar Panel Upgrade
Every one who ever sees this post is going to ask:
How are they attached to the roof? How are they secured while the trailer is in motion? Or, do they have to be?
Can you show us what the "mounting frame" is and how it works? How did you get on to the roof to install it all?
Where/how does the wiring enter the trailer? How/where is the solar controller?
Beautiful install. There have been several other installs of "tiltable" panels done in different ways, and each have been pretty remarkable achievements.
This install was pretty amazing for...2017.
320 "closet"
Decided I needed to better use the tiny bit of underutilized space. We hadn't used the TV for a couple of years!
Re: NuCamp recall for certain 2023-2024 nuCamp TAB 400, Cirrus 620, and 820's with the Lithium Upgrade
As I've been building a parts list to install a Multiplus 3000 in my 2021 T@B 400, one of the things I wondered about was the disconnect switch nuCamp uses. I had already purchased a 400 Amp disconnect and was planning on replacing the existing one for the exact reason this recall is happening...Glad I did!
Re: NuCamp recall for certain 2023-2024 nuCamp TAB 400, Cirrus 620, and 820's with the Lithium Upgrade
thank Thanks @ pthomas745. I put it under the Service, Maintenance and Recall category.
Re: Alde Fluid Never Changed - Problems?
The anti-corrosive properties of the glycol degrade more over time than use. That's the reason for a two year time frame rather than the amount time the Alde actually ran. Look for bulging around the convectors like in the attached picture to know if you have a problem. If you don't see bulging, you are probably safe to assume that all it need is a glycol exchange (preferably to the Rhomar fluid).
Re: Ideas on Tab 360
Using the information posted here from Vogel’s RV a few basic drawing were created to better understand / visualize what the 360 could be.
These visualizations have three assumptions:
= 1 = 360 is a 400 with 1.5 feet cabin length removed forward of axle.
= 2 = 360 has a 320 Kitchen and Wetbath (slightly wider kitchen area).
= 3 = Only sleeping position is shown (no idea what Dinette might be).
At this time my biggest concerns/worries are:
++ A ++ Dinette Design as I've never found any RV dinette seating to be as comfortable as the 320S rear bench seat with the upright and recline positions. Just copying the 320 would be ideal for me.
++ B ++ Air Conditioner, Coolcat or Air8 will both eat up storage space . . . a correctly sided/vented sidewall mounted A/C would be just fine with me.
These visualizations have three assumptions:
= 1 = 360 is a 400 with 1.5 feet cabin length removed forward of axle.
= 2 = 360 has a 320 Kitchen and Wetbath (slightly wider kitchen area).
= 3 = Only sleeping position is shown (no idea what Dinette might be).
At this time my biggest concerns/worries are:
++ A ++ Dinette Design as I've never found any RV dinette seating to be as comfortable as the 320S rear bench seat with the upright and recline positions. Just copying the 320 would be ideal for me.
++ B ++ Air Conditioner, Coolcat or Air8 will both eat up storage space . . . a correctly sided/vented sidewall mounted A/C would be just fine with me.
Re: 2024 Tab 400 Q- inverter and access to under mattress
Appreciate your comments and pics!
Re: 2024 Tab 400 Q- inverter and access to under mattress
I keep the panel over the batteries screwed down as the panel can move a little and the drawer latch below the bed is finicky on mine (already had to add shims to a slider and latch) to keep drawer closed during travel.
For the panel over the Alde, I added a "D ring" near where RTWCTS drilled a hole.
For the panel over the Alde, I added a "D ring" near where RTWCTS drilled a hole.