Format changes are still occurring as we identify issues. We have made some font changes to improve readability and are working on restoring options that were available in the old forum version. Please comment on your findings and suggestions.
Thanks
qhumberd
Moderator
Thanks
qhumberd
Moderator
Best Of
Maxxair Plus fan - installing a Fanmate rain cover is very simple
Our 2024 320s BD came with a Maxxair Plus fan. It's a good fan, but we do need to keep an eye on the weather as a windy downpour could mean water in the trailer. The Plus model has four prongs on its rooftop mounting flange. These allow quick and easy mounting of a Fanmate rain cover. The cover is held on with four pins that engage the mounting prongs.
Photo shows the two prongs on the passenger side of the fan's mounting flange.
Above shows the Fanmate cover mounted with pins to the mounting prongs. The pins are self retaining.
Another view of the mounting. Once you figure out the alignment, removing or mounting the cover is a ten minute job using a good stepladder.
Photo shows the two prongs on the passenger side of the fan's mounting flange.
Above shows the Fanmate cover mounted with pins to the mounting prongs. The pins are self retaining.
Another view of the mounting. Once you figure out the alignment, removing or mounting the cover is a ten minute job using a good stepladder.
Re: Portable Gas Grill for 2025 T@B 400
I have a Weber BabyQ at home. This is too big and heavy for light weight camping. In my opinion, the smallest grill to get the job done is the way to go. Not for size and weight, but for clean up. So I have been using a Coleman Fold-N-Go for years now. It is small and since there is less there, there is less to clean.
Re: TAB400 Bathroom door hinge source
I was able to get replacements from Build.Com. They are a heavy duty steel and work fantastic on the bathroom door and only $1.74 each. 👍 https://www.build.com/hardware-resources-22855-10/s1434918?uid=3374503#overview
Re: where is the battery cut off on a 2012 320
Battery cut-offs didn't become standard equipment until (I think) 2016 or 2017. I installed my own in my 2015. It was a common DIY mod and a hot topic of discussion on the forum when I first joined. Times have changed! :-)
Re: 320 Cassette jammed
Glad you got it! The first time I used it I found that the cover prevented the latch on the bottom of the cassette from locking into place. I removed it and have not had a problem since.
Re: 320 Cassette jammed
Thanks to @SLJ and @Mobean After verifying the rotating knob could not be straighter, and after pulling the cassette as far out as it could go, I pushed down mightily on the cassette inside and wife pulled less aggressively but hard and we got it out. No damage but will not use the lower plate anymore. Thanks everyone.
Re: Battery Not Holding Charge
Just replaced the AGMs in our 400 with LiTime lithiums (200ah). Time will tell about quality but we have way more usable power now. We’re able to easily run two refrigerators (the stock isotherm and an external 12v cooler) and keep the vent fan on all day. Solar helps but isn’t as needed now. No more power anxiety.
Re: Extending Stabilizer Reach
While there are good things with these attached pads to help the reach of the stabilizers, it should also be noted that you increase the risk of bending the whole mechanism if you happen to go through the approach apron of some business that is too steep.
I say this because it happened to me recently. I pulled into a coffee shop and was able to enter just fine, but the approach leaving the establishment was much steeper and the result was both of the front stabilizer ended up bent beyond repair and that was without these extension pads. A couple of blocks carried along and placed beneath as you set up may seem inconvenient but has its advantages.
nbrandt
2018 T@B 400 / (soon 2021 T@B 320
2015 Tundra 4.6
2015 Tundra 4.6
Re: Leaking Shower Control Valve 2021 T@B 400
@manyman297
Thanks about the suggestion of checking the bonnet nut. I have not had a chance to dig into it yet, because we're on the road. But that is something I'll definitely look at. I also contacted new camp tech and got a part number for a new control valve if I need one.
In case anyone else needs it, the part number it is:
Hot & cold mixer valve - Part number 68-60-553
Thanks about the suggestion of checking the bonnet nut. I have not had a chance to dig into it yet, because we're on the road. But that is something I'll definitely look at. I also contacted new camp tech and got a part number for a new control valve if I need one.
In case anyone else needs it, the part number it is:
Hot & cold mixer valve - Part number 68-60-553
Re: Camping in triple digits a bad idea?
I agree w @marchule. But I think it’s a bad idea to do anything in 100+ deg heat! Trying to become familiar w a new camper for your first time in extreme heat might just be a lesson in frustration. If something doesn’t work quite right you wouldn’t know if it’s operator error, mechanical issues, or just too hot.
I’d get the trailer home, “camp” in your driveway a few nights under less extreme conditions if you can, and learn the different systems in the trailer.
I’d get the trailer home, “camp” in your driveway a few nights under less extreme conditions if you can, and learn the different systems in the trailer.
Besides, what the heck can you do when it’s 110??
